High Strength Epoxy For Concrete Mounting System

Epoxy Anchor Mortar For Solar Panel Fixing / Chemical anchors factory in Taiwan for strong fixings, heavy duty load, structure reinforcement, repair. 20 years experience in OEM, private label, export worldwide and distributors all over the world.

High Strength Epoxy For Concrete Mounting System - High temperatures dual component pure epoxy chemical anchor
  • High Strength Epoxy For Concrete Mounting System - High temperatures dual component pure epoxy chemical anchor

High Strength Epoxy For Concrete Mounting System

GU-500SD 400ml 3:1

Epoxy Anchor Mortar For Solar Panel Fixing

High strength epoxy anchoring for aluminum solar panel concrete mounting system. Top-quality epoxy can sustain under high heat and heavy loading.

Ultimate performance for rebar connections, heavy anchoring on dry concrete, wet concrete, cracked and uncracked concrete. Advanced-formula pure epoxy adhesive is workable at wide temperature and crucial anchoring. Quality tested and approved by Germany lab. Non-sag allows for overhead and suspended ceiling application. There is also 585ml available in the range.

Chemical fixing system - Ultimate performance pure epoxy chemical anchor

High-end epoxy mortar for heavy anchoring and critical conditions. In variation case of anchoring work which required higher performance to satisfy and secure the anchoring in dry, wet, uncracked, cracked concrete even in seismic conditions or temperature variation and installation limitation. We tested diverse anchoring condition in ETAG approval lab and with report to compare. Epoxy injectable adhesive anchor is strongest one of bonding fasteners which is growing demands.



Specification of GU-500SD Pure epoxy chemical anchor
  • Material: Pure Epoxy
  • Model Number: GU-500SD
  • Size: 400ml
  • Shelf Life: 18 months
  • Mixing Ratio: 3:1
  • Mixing Color: Orange
  • Standard Package: One cartridge with one mixer
  • Other Accessory: Mixer, caulking gun, nylon sleeve, air pump, brush
Good Use pure epoxy chemical anchor has good performance on wet holes and cracked concrete
  • Heavy duty loading
  • Non-sag for overhead and wall application
  • Good performance on wet and cracked concrete holes
  • Ideal for deep embedment and large holes
  • Provide longer working time
  • No shrinkage
  • Orange color for easy monitoring
  • Styrene free, low odor, and LEED tested for VOC (Volatile Organic Compounds)
  • No health or safety concern to slow down your work
  • ETA in process.
All Good Use chemical anchors have done sustained loads test at IWB lab in Germany

There is no qualified lab with equipment for testing bonding anchor according ETA regulations in Asia. All our items are tested by EAD 330499-00-0601 which is comprehensive plan for both of rebar and threaded rods. We cooperate and consult with leading experts in Europe who dedicate in the fasteners field for more than two decades. We keep improving our research capacity and upgrade international approvals of chemical anchor.

Epoxy chemical anchor for solar panel fixing

There are many innovative ways of solar panel design and installation. This is special case and request in USA for bonding aluminum frame on concrete track rail. Non-standard anchoring that sustained bonding under high heat and windy are required. We look for more possibility and challenge of chemical anchor.

Strongest epoxy anchoring for all fixing solution

Non-drip formula, ideal for overhead installation and suspension anchorage. Versatile and multi-purpose pure epoxy is longer curing time and more flexible on applications. As global warming, climate suitability and wide temperature applicability are important for chemical anchor development. We equip temperature facilities to simulate different anchoring temperature worldwide and do multiple testing to ensure the quality. The steady characteristic of epoxy is most used in tropical zone.

Technical Data

CHART 1. SOLID SUBSTRATE REBAR INSTALLATION DETAILS

Pressure Destroy Haul Strength (Kgf/KN) Safety Haul Strength (Kgf/KN) Working Standard (mm)
Concrete Strength 4,000 psi 280 kg/cm2 4,000 psi 280 kg/cm2 Hole Diameter Hole Depth
Rebar No. #3 (Φ10) 3,622 36.6 1,207 12.2 13 90
#4 (Φ12) 6,437 65.0 2,146 21.7 16 125
#5 (Φ16) 9,737 98.4 3,246 32.8 20 145
#6 (Φ20) 13,715 138.5 4,572 46.2 25 170
#7 (Φ22) 18,754 189.4 6,215 63.1 28 200
#8 (Φ25) 24,137 243.8 8,046 81.3 32 225
#9 (Φ28) 27,484 277.6 9,161 92.5 37 260
10 (Φ32) 31,869 321.9 10,623 107.3 40 290
11 (Φ36) 36,000 363.6 12,000 121.2 42 320
Remarks: 1. Concrete Strength fc': 280kg/cm2 (4,000 psi)
2. Rebar Strength: #3~#5 fy: 2,800 kgf/cm2, #6~#11 fy= 4,200 kgf/cm2

CHART 2. CURING TIME TABLE

Temperature (°C) Gelling Full Curing
5~9 2 hr. 90 hr.
10~14 90 min. 64 hr.
15~19 45 min. 28 hr.
20~29 30 min. 18 hr.
30~39 20 min. 7 hr.
40 12 min. 5 hr.
Please make pull off test for at least 24 hours after full cured.

CHART 3. FIXING CONSUMPTION PER CARTRIDGE

Anchor Size Hole Diameter
(mm)
Hole Depth
(mm)
Number of Fixings
400ml
M8 10 80 80
M10 13 90 42
M12 16 120 21
M16 20 145 11
M20 25 170 6
M24 28 210 4
M30 35 270 2
M36 40 330 1
Note: Based on continuous installation without interruptions or nozzle changes. Provided as a guide and will vary with temperature.
How to use a caulking gun?

1. There is a small trigger on the back of the caulking gun. Press the release trigger with your thumb. This will loosen the long steel rod that runs through the entirety of the frame. 2. Pull the plunger all the way back. 3. Remove the white cap and plug of tube and then screw the mixer nozzle on to the tube. Insert the flat end of the tube into the back of the gun first and put the tube with the mixer nozzle in the front. Pull the handle trigger to move the plungers of caulking gun. Make sure that the plungers of caulking gun are in the center of tube pistons. It is very important to put the tube in the correct position.



Related Products
400ml Tropical Epoxy Chemical Anchor - 400ml two part epoxy resin anchoring adhesive
400ml Tropical Epoxy Chemical Anchor
GU-500 400ml 3:1

400ml epoxy chemical anchor is 3:1 injectable cartridge for rebar connections and heavy anchoring....

Details
High Temperature Epoxy Anchoring - 650ml two components pure epoxy summer epoxy adhesive
High Temperature Epoxy Anchoring
GU-500 650ml 1:1

1:1 ratio 650ml epoxy base injection mortar for anchoring projects in high temperature country. Two...

Details
Epoxy Chemical Anchor For Varying Weather - Epoxy anchor for different climate conditions
Epoxy Chemical Anchor For Varying Weather
GU-500SD 400ml 3:1

GU-500SD 400ml is strongest in all chemical anchoring. Remarkable at cold weather, cracked...

Details
400ml dual component manual caulking gun - Cartridge guns - #810
400ml dual component manual caulking gun
#810

#810 caulking gun is a price option for two component epoxy 400ml cartridge with mixing ration...

Details
400ml dual component manual caulking gun - Cartridge guns - G34-400LA
400ml dual component manual caulking gun
G34-400LA

G34-400LA dispenser is heavy-duty and efficient dispensing for 3:1 400ml epoxy adhesive. High...

Details
Mixing nozzle for 1:1 and 3:1 chemical anchor - Static mixer for 1:1 and 3:1 chemical anchor
Mixing nozzle for 1:1 and 3:1 chemical anchor
#818

Static mixer nozzles are applied to adhesive cartridges to mix and dispense two component adhesives....

Details
Files Download
Pure Epoxy Catalogue
Pure Epoxy Catalogue

Bonding strength table on dry concrete by different hole sizes and depth. Especially for big diameter rebars/threaded rods.

Download
GU-500SD 400ml Pure Epoxy Technical Data Sheet
GU-500SD 400ml Pure Epoxy Technical Data Sheet

Technical information of anchor design, curing time, edge distance, consumption per hole and installation procedure for GU-500SD pure epoxy.

Download
Gallery

High Strength Epoxy For Concrete Mounting System | Chemical Anchor Manufacturer - Good Use

Good Use Hardware Co., Ltd. is one of prime High Strength Epoxy For Concrete Mounting System | chemical anchors suppliers based in Taiwan since 1997.

Certified chemical anchor solutions with wide selections of adhesive materials including epoxy anchors, concrete anchors, resin anchors for heavy loads in rebar application, diamond drilled holes and anchoring in solid concrete. Non-drip formula, ideal for overhead installation. Chemical anchor bolt and anchor fixings included for efficient, hassle-free, labor-saving chemical anchoring.

Good Use has been offering customers certified tested high-quality chemical anchors. Both with advanced technology and 20 years of experience, Good Use ensures each customer's demands are met.